Mecmesin | Search results

1526

^{[Page extract]}

ASTM D3471

This test method covers the determination of the top-load required to engage lugs on Type IA child-resistant closures.

1527

^{[Page extract]}

ASTM D5321-12

This test method covers a procedure for determining the shear resistance of a geosynthetic against soil, or a geosynthetic against another geosynthetic, under a constant rate of deformation.

1528

^{[Page extract]}

ASTM D2344 is a test method, which determines the short-beam strength of high-modulus fiber-reinforced composite materials. It is applicable to all types of parallel fiber reinforced plastics and composites.

1529

^{[Page extract]}

ASTM D3826

ASTM D3826 is a tensile test method, which covers a degradation-end point, or a brittle point) for degradable polyethylene/polypropylene films and sheeting less than 1.0 mm thick.

1530

^{[Page extract]}

ISO 8510-2

Specifies a 180° peel test for the determination, under specified conditions, of the peel resistance of a bonded assembly of two adherends where one adherend is flexible and the other is rigid.

1531

^{[Page extract]}

BS EN ISO 13262

BS EN ISO 13262 is test method to determine the tensile strength of seams on thermoplastics spirally-formed structured-wall pipes.

1532

^{[Page extract]}

BS EN ISO 22088-2

BS EN ISO 22088-2 is a test method for determining the environmental stress cracking of plastics. This has replaced BS EN ISO 6252:1998

1533

^{[Page extract]}

SAE J1525

This SAE Recommended Practice describes a lap shear test method for use in measuring the bonding characteristics of automotive-type adhesives for joining fiber reinforced plastics to themselves and to metals.

1534

^{[Page extract]}

ASTM D6713-14

Materials shall be tested and the individual grades shall conform to specified values of the physical properties such as tensile strength, tensile elongation, tensile modulus, dimensional stability, flexural modulus, and Izod impact; and dimensional pro

1535

^{[Page extract]}

BS EN ISO 80369-7

This part of ISO 80369 specifies dimensions and requirements for the design and functional performance of small-bore connectors intended to be used for connections in intravascular applications or hypodermic connections in hypodermic applications of med

1536

^{[Page extract]}

FINAT FTM3

This test method allows the end user to determine the force required to separate the release backing from the pressure sensitive adhesive coated face material.

1537

^{[Page extract]}

ASTM D4476 / D4476M-14

ASTM D4476 is a test method used to determine the flexural properties of fiber-reinforced pultruded plastic rods. The specimen used is a rod with a semi-circular cross section, moulded or cut from lengths of pultruded rods.

1538

^{[Page extract]}

ASTM C907

This test method covers a laboratory procedure for determining the tensile adhesive strength of a preformed tape sealant. The type of failure can be determined, and the degree of cohesive/adhesive failure can be estimated.

1539

^{[Page extract]}

CETIE Guide 3

This guide is for producers of quality sparkling wines who carry out the secondary fermentation process in the bottle, also known as bottle fermentation.

1540

^{[Page extract]}

ASTM C364

This test method covers the compressive properties of structural sandwich construction in a direction parallel to the sandwich facing plane.

1541

^{[Page extract]}

MIL AS23190A

AS23190 is a procurement specification that covers a series of plastic and metal components and devices used for the tying, positioning, and supporting cable, cable assemblies, wire, and wire bundles in electrical, electronic and communication equipment

1542

^{[Page extract]}

ASTM D2918

This test method provides data for assessing the durabilities of adhesive joints by means of T-peel type specimens stressed in contact with air, air in equilibrium with certain solutions, water, aqueous solutions, or other environments at various temper

1543

^{[Page extract]}

NF S86-604

This document defines the test methods for characterizing metallic watch straps and the corresponding requirements.

1544

^{[Page extract]}

ASTM C598

This test method covers the determination of the annealing point and the strain point of a glass by measuring the rate of midpoint viscous bending of a simply loaded glass beam.

1545

^{[Page extract]}

BS EN ISO 527-2

ISO 527-2 specifies the test conditions for determining the tensile properties of moulding and extrusion plastics, based upon the general principles given in ISO 527-1.

1546

^{[Page extract]}

BS EN 5350-C5

Adhesives, Test methods, Adhesive strength, Longitudinal, Strength of materials, Shear strength, Dimensional tolerances

1547

^{[Page extract]}

ASTM C1161

This test method covers the determination of flexural strength of advanced ceramic materials at ambient temperature. Four-point and three-point loadings with prescribed spans are the standard.

1548

^{[Page extract]}

ASTM D5467 / D5467M-97

ASTM D5467 is a test method that determines the in-plane compressive properties of polymer matrix composite materials reinforced by high-modulus fibers in a sandwich beam configuration.

1549

^{[Page extract]}

ASTM D3810

This test method covers the determination of or the recommendation for minimum application torque that results in a fully degraded removal torque that is at a level greater than the maximum expected reverse-ratchet torque for a Type IA child-resistant c

1550

^{[Page extract]}

ISO 527-4

ISO 527-4 determines the tensile properties of isotropic and orthotropic fibre reinforced plastic composite sheeting and film including the tensile strength and modulus of elasticity, strain, elongation and the tensile energy to break (TEB).