Search results
1726
[Page extract]
TAPPI T 284
This test evaluates the ability of corrugating medium to contribute to the compression strenght of a corrugated box.
1727
[Page extract]
ASTM D3164
Test method ASTM D3164 is used to produce shear strength data for joints to compare adhesives or evaluation surface treatments. Shear joints impose uniform stresses across the bond area which results in the highest possible joint strength.
1728
[Page extract]
NF S86-604
This document defines the test methods for characterizing metallic watch straps and the corresponding requirements.
1730
[Page extract]
BS EN ISO 527-2
ISO 527-2 specifies the test conditions for determining the tensile properties of moulding and extrusion plastics, based upon the general principles given in ISO 527-1.
1731
[Page extract]
ASTM D3330
These test methods cover the measurement of the peel adhesion of single and double-sided pressure-sensitive tapes.
1732
[Page extract]
ASTM D5379/D5379M-05
This test method covers the shear properties of composite materials reinforced by high-modulus fibers. The composite materials are limited to continuous-fiber or discontinuous-fiber-reinforced composites in specific forms.
1733
[Page extract]
ASTM D5467 / D5467M-97
ASTM D5467 is a test method that determines the in-plane compressive properties of polymer matrix composite materials reinforced by high-modulus fibers in a sandwich beam configuration.
1734
[Page extract]
ASTM F1839-08
This specification covers rigid polyurethane foam blocks or sheets recommended for use as a standard material for mechanical testing using orthopedic devices and instruments.
1735
[Page extract]
ASTM F806-99a
ASTM F806 is a test method that covers determination of the short-time compressibility and recovery at room temperature of laminated composite gasket materials.
1736
[Page extract]
ASTM D3472
This test method covers the measurement of the torque developed when Type IA child-resistant closures are rotated in the counter-clockwise direction.
1737
[Page extract]
ISO 8510-2
Specifies a 180° peel test for the determination, under specified conditions, of the peel resistance of a bonded assembly of two adherends where one adherend is flexible and the other is rigid.
1738
[Page extract]
ISO 21180
ISO 21180 specifies a test method for the determination of the maximum tensile strength of light conveyor belts.
1739
[Page extract]
BS EN 2591-420
Aircraft components, Air transport engineering, Electrical connections, Electric connectors, Optical fibres, Fibre optic connectors, Test methods, Strength of materials, Tensile strain, Torsional strength, Bending stress.
1740
[Page extract]
SAE J1525
This SAE Recommended Practice describes a lap shear test method for use in measuring the bonding characteristics of automotive-type adhesives for joining fiber reinforced plastics to themselves and to metals.
1741
[Page extract]
ASTM D4776 / D4776M-18
ASTM D4776 is a test method used to determine the maximum adhesion force of tyre cords in rubber compounds.
1742
[Page extract]
ASTM D3480
These test methods cover the measurement of the downward force required to open or activate child-resistant snap-engagement packages.
1743
[Page extract]
ASTM D6264 /D6264M-17
In ASTM D6264 a quasi-static indentation (QSI) test method is used to obtain quantitative measurements of the damage resistance of a continuous-fibre-reinforced composite material to a concentrated indentation force
1744
[Page extract]
ASTM D937-97
1.1 This test method covers measuring with a penetrometer the penetration of petrolatum as an empirical measure of consistency.
1745
[Page extract]
ASTM D2063/D2063M
This test method measures torque retention properties of container/continuous thread closure systems with the use of a non-automated, spring torque-meter (with either a dial indicator or a digital readout) or a torque wrench. evaluation.
1746
[Page extract]
BS EN 1394
BS EN 1394 is a tensile test method to determine the initial circumferential tensile strength of plastic pipes.
1747
[Page extract]
ASTM D2344 / D2344M
ASTM D2344 is a test method, which determines the short-beam strength of high-modulus fiber-reinforced composite materials. It is applicable to all types of parallel fiber reinforced plastics and composites.
1748
[Page extract]
ASTM D3826
ASTM D3826 is a tensile test method, which covers a degradation-end point, or a brittle point) for degradable polyethylene/polypropylene films and sheeting less than 1.0 mm thick.
1749
[Page extract]
BS EN ISO 80369-7
This part of ISO 80369 specifies dimensions and requirements for the design and functional performance of small-bore connectors intended to be used for connections in intravascular applications or hypodermic connections in hypodermic applications of med
1750
[Page extract]
FINAT FTM3
This test method allows the end user to determine the force required to separate the release backing from the pressure sensitive adhesive coated face material.