Search results
1576
[Page extract]
ASTM F2256-05
This test method is intended to provide a means for comparison of the adhesive strengths of tissue adhesives intended for use as surgical adhesives or sealants, or both, on soft tissue.
1577
[Page extract]
ISO 9073-3
Application of a force longitudinally to a test piece of a specified length and width at a constant rate of extension. Determination of values for breaking strength and elongation from the recorded force-elongation curve.
1578
[Page extract]
TAPPI T 807
This method describes a procedure for measuring the bursting strength of linerboard using a disk shaped diaphragm. Basis weights for this method should be 98 g/m (20#/MSF) and higher. The minimum burst should be 350 kPa (51 psi).
1579
[Page extract]
ASTM D7084-04
1.1 This test method covers the determination of bulk crush strength of a bed of formed catalyst particles 1⁄32 to 3⁄16 in.
1580
[Page extract]
ASTM D5458-95
This test method measures cling between two layers of film, in both a stretched and unstretched condition.
1581
[Page extract]
BS EN 12209
BS EN 12209:2016 specifies requirements and test methods for the durability, strength, security, and function of mechanically operated locks and latches and their locking plates for use in doors, window doors and entrance doors in buildings.
1582
[Page extract]
ASTM D5649-01
This test method is used to make comparative assessments of the securing or locking effect of adhesives used in threaded assemblies.
1583
[Page extract]
CETIE Guide 18
This document provides a collection of test methods for the qualification of plastic flat-top closures applied on PET bottles that are used in the beverage industry.
1584
[Page extract]
EN 14509
This draft European Standard is submitted to CEN members for second formal vote. It has been drawn up by the Technical Committee
CEN/TC 128.
This covers a very wide range of tests including coatings, strengths etc.
1585
[Page extract]
EN 149
EN149 specifies minimum requirements for filtering half masks as respiratory protective devices to protect against particles except for escape purposes.
1587
[Page extract]
ASTM D3575
ASTM D3575 covers a number of tests for determining properties of polyethylene foams including compressive strength.
1588
[Page extract]
*corp Ikea IOS-TM-0057
This instruction describes preparation and testing of a board's ability to hold a fastener in up to three orientations
1589
[Page extract]
ASTM F1995-12
This test method covers the determination of the shear integrity of materials and procedures used to attach surface mount devices (SMD) to a membrane switch circuit.
1590
[Page extract]
ASTM C651
This test method covers determination of the flexural strength of manufactured carbon and graphite articles using a simple beam in four-point loading at room temperature.
1591
[Page extract]
ISO 9895
Specifies a method for determining the compressive strength in the machine and cross-directions of paper and board using a short-span compressive tester. It is intended for papers and boards used for the manufacture of containers and boxes.
1592
[Page extract]
Vice grip (Mechanical)
Vice grips (single-action) - having one fixed jaw against which a second parallel jaw is tightened. The position of the fixed face may be adjustable to accommodate differing specimen thickness.
1593
[Page extract]
ASTM D3810
This test method covers the determination of or the recommendation for minimum application torque that results in a fully degraded removal torque that is at a level greater than the maximum expected reverse-ratchet torque for a Type IA child-resistant c
1594
[Page extract]
ISO 527-3
ISO 527-3 specifies the conditions for determining the tensile properties of plastic films or sheets less than 1 mm thick, based upon the general principles given in ISO 527-1.
1596
[Page extract]
*corp Ford DSEU
Test method covering measurement of door slam energy for Ford Chenai, India. Shows Mecmesin loadcell, display and special gripping fixtures. Note: Diagram shows a rigid link bar, which was later replaced by a flexible bungee connection.
1597
[Page extract]
BS 6319-7
BS 6319-7 is a test method for determining the tensile strength of resin and polymer/cement compositions for use in construction.
1598
[Page extract]
ASTM D3950
This specification covers nonmetallic strapping and joining methods for closing, reinforcing, and bundling materials for shipment, unitizing, palletizing, and bracing for car and truck loading.
1599
[Page extract]
ASTM F1304-18
ASTM F1304 is a test method used to determine the deflection of relatively rigid resilient floor tile such as vinyl composition tile and resilient flooring with a rigid polymeric core.
1600
[Page extract]
BS ISO 7322
This International Standard specifies test methods for the determination of the following characteristics of composition cork (= product obtained from the agglutination of cork granules with the addition of a binder generally not derived from cork cells