Mecmesin | Search results

1626

^{[Page extract]}

ASTM E855-08

This standard describes three test methods for determining the modulus of elasticity in bending and the bending strength of metallic strips or sheets intended for the use in flat springs.

1627

^{[Page extract]}

CETIE Guide 18

This document provides a collection of test methods for the qualification of plastic flat-top closures applied on PET bottles that are used in the beverage industry.

1628

Event

Makers Hackathon, June 16-18th 2022, Malmö, Sweden

Who should attend? Quality Managers, design/product engineers and materials specialist. What is the exhibition about?

1629

^{[Page extract]}

ASTM D5618-94

This test method covers the measurement of barnacle adhesion in shear to surfaces exposed in the marine environment. It is used to establish the ability of a surface to reduce biofouling adhesion.

1630

^{[Page extract]}

The purpose of DD CEN/TS 15945 is to specify test methods to evaluate the ease of opening of consumer packages, in order to improve easy access to the contents. For packages regulated for safety or similar reasons, e.g.

1631

^{[Page extract]}

ASTM F2256-05

This test method is intended to provide a means for comparison of the adhesive strengths of tissue adhesives intended for use as surgical adhesives or sealants, or both, on soft tissue.

1632

^{[Page extract]}

EN 149

EN149 specifies minimum requirements for filtering half masks as respiratory protective devices to protect against particles except for escape purposes.

1633

^{[Page extract]}

ISO 3781

Specifies a test method for the determination of the wet tensile strength of paper or board after its immersion in water for a specified period.

1634

^{[Page extract]}

ASTM D1004

ASTM D1004-13 covers the determination of tear strength or tear resistance of flexible plastic film and sheeting. The site of tear is initiated by a high stress concentration caused by the 90° angle in the specimen.

1635

^{[Page extract]}

ASTM D5458-95

This test method measures cling between two layers of film, in both a stretched and unstretched condition.

1636

^{[Page extract]}

ASTM D3575

ASTM D3575 covers a number of tests for determining properties of polyethylene foams including compressive strength.

1637

^{[Page extract]}

ASTM C480

This test method covers the determination of the creep characteristics and creep rate of flat sandwich constructions loaded in flexure, at any desired temperature.

1638

^{[Page extract]}

ASTM D5649-01

This test method is used to make comparative assessments of the securing or locking effect of adhesives used in threaded assemblies.

1639

^{[Page extract]}

*corp Ikea IOS-TM-0057

This instruction describes preparation and testing of a board's ability to hold a fastener in up to three orientations

1640

^{[Page extract]}

ASTM D3469

These test methods measure the downward forces during the disengagement of lug-style caps from their respective containers. The methods measure the maximum torque developed while the cap is further disengaged by turning of the container.

1641

^{[Page extract]}

Vice grip (Mechanical)

Vice grips (single-action) - having one fixed jaw against which a second parallel jaw is tightened. The position of the fixed face may be adjustable to accommodate differing specimen thickness.

1642

^{[Page extract]}

*corp Ford DSEU

Test method covering measurement of door slam energy for Ford Chenai, India. Shows Mecmesin loadcell, display and special gripping fixtures. Note: Diagram shows a rigid link bar, which was later replaced by a flexible bungee connection.

1643

^{[Page extract]}

ISO 527-3

ISO 527-3 specifies the conditions for determining the tensile properties of plastic films or sheets less than 1 mm thick, based upon the general principles given in ISO 527-1.

1644

^{[Page extract]}

ASTM D3950

This specification covers nonmetallic strapping and joining methods for closing, reinforcing, and bundling materials for shipment, unitizing, palletizing, and bracing for car and truck loading.

1645

^{[Page extract]}

ISO 9895

Specifies a method for determining the compressive strength in the machine and cross-directions of paper and board using a short-span compressive tester. It is intended for papers and boards used for the manufacture of containers and boxes.

1646

^{[Page extract]}

BS EN 12311-2

BS EN 12311-2 is a test method for determining the tensile properties of flexible sheets used for waterproofing roofs.

1647

^{[Page extract]}

BS ISO 7322

This International Standard specifies test methods for the determination of the following characteristics of composition cork (= product obtained from the agglutination of cork granules with the addition of a binder generally not derived from cork cells

1648

^{[Page extract]}

BS EN ISO 14129

BS EN ISO 14129 is a test method used to determine the in-plane shear stress/shear strain response of fibre-reinforced plastic components.

1649

^{[Page extract]}

SAE J 1553

This SAE Recommended Practice describes a cross peel test method for use in measuring the bonding characteristics of automotive-type adhesives for joining fiber-reinforced plastics to themselves and to metals.

1650

^{[Page extract]}

BS ISO 3384-1:2001+A1

BS ISO 3384-1 is a test method for determining the stress relaxation in compression of vulcanised rubber or thermoplastic.